Antec Overture 2 ATX Desktop Case

Reviews: Cases

Author:
Editor:
Sponsor:
Published:

Kurtis Kronk
Brian
Antec
Nov. 10, 2005

<< Previous

Next >>

Quality Check

My quality check basically consists of three things: Structural Integrity, Installation, and Safety. My structural integrity testing is where I apply pressure to the case from different directions and check to see if the frame can be easily bent or twisted out of shape. Installation is the process of installing the various system components and making sure that installation goes smoothly. Lastly, the safety testing is a result of the installation process. After installing everything, I should be left without open wounds, but if I am wounded in battle I will make note of it and warn you which trouble areas to watch out for.

Structural Integrity

I wasn't really sure what to expect in terms of durability with this case. With the case closed and on its side, I gave it my usual push-n-twist test, and it was solid. Of course, the case isn't meant to be on its side as you'll be blocking an exhaust, so I put it flat and did the same test... as expected it felt just as solid. Since you will probably be putting a monitor on top of the case, I also tried pushing straight down on the top panel. With force, it flexed a little bit, but nothing that I'd be worried about. That said, I would be a little scared to set my 22" ViewSonic P225fb CRT (all 80 some-odd pounds of it) on top of this case. I would feel much better placing something a bit lighter like my Dell 2005FPW LCD on top of it.

Installation

Installation went quite well with the Overture 2. Aside from some minor gripes which I noted earlier, I didn't run into any problems. I was surprised how well everything fit into the case, and although it took me a while, I was even able to get my cable management looking pretty darn good, if I may say so myself. It would have been nice to have more toolless features, but with a case this size, chances are you won't want to open it up and tool around inside it very often anyways.

Safety

The only problem I had with this case where safety is concerned is with the PCI slot covers with holes in them for airflow. When I was removing them I sliced up my hands a little bit until I figured out that it would be much easier to remove them with the aid of a screwdriver. After fiddling with this case for countless hours, I can say that it is quite safe, aside from the aforementioned PCI slot covers. Almost every edge is either folded or rolled.

<< Previous

Page 4 of 5

Next >>

Page 1: Introduction
Page 2: First Impressions / Opening the Case
Page 3: Inside the Case
Page 4: Quality Check
Page 5: Conclusion / Update

Subscribe to Desktop [more info]

View All

Desktop April 22, 2007

HighSpeedPC Tech Station

Desktop April 3, 2006

Add Comment

18 User Comments

1 - Posted by Rich on August 24, 2005 - 2:08 pm

Antec makes some great cases. I have been a fan of their Minuet series for basic PC builds. It has the same good styling as the overture but it is a half-height case which limits components significantly.

2 - Posted by Kurtis on August 24, 2005 - 2:32 pm

this is a half-height case... and it didn't really limit the components that much, aside from the # of HDDs you can have. i could see running an SLI system in this case with ease.

3 - Posted by Rich on August 24, 2005 - 5:18 pm

I meant you could only use half-height PCI/AGP cards in the minuet. It is very thin

Minuet
3.8"(H) x 16.8"(D) x 12.75"(W)

Overture II
5.25"(H) x 17"(W) x 19.25"(D)

The minuet only supports microATX boards while the overture supports both ATX and microATX. I think the overture is the much more functional of the two unless you have no upgrade plans.

4 - Posted by Kurtis on August 24, 2005 - 5:54 pm

hm... that is thin. lol

come to think of it i have built a system in a minuet before and it is much more cramped.

5 - Posted by mike on August 24, 2005 - 7:18 pm

i have a minuet as well. get a lot of comments on it.

6 - Posted by Rich on August 25, 2005 - 7:25 am

Antec's paint finishes are some of the nicest I have seen, especially for the price they charge.

7 - Posted by handrail on August 25, 2005 - 8:24 am

werd. antec's cases rock. i love my SLK3700AMB.

8 - Posted by Guest on September 8, 2005 - 7:12 pm

how did the replacement PSU go with the noise problem

I have requested a replacement PSU so I can see if there is a problem with mine or if this is normal. I'll update the review later regarding this issue if I do receive a replacement.

9 - Posted by Guest on September 19, 2005 - 4:27 pm

My Overture 2 came in an Overture 1 box (reference to a 380W PSU on the box art) and it's really noisy. I'm wondering if it was one of the first batch, though I only bought it about a week ago. I was thinking of replacing the fan but dismantling it all would be kind of demoralising.

10 - Posted by Solburn on October 26, 2005 - 8:54 am

I bought the case last week. I'll be using it for HTPC because its a very nice looking Desktop with full pci slots, enough room for a Zalman 7700 and its fits pretty nicely by Audio cases but does not cost a fortune.

My PSU fan doesn't sound loudly at all. I connected the PSU fan connector on my motherboard, so the speed maybe controlled by the motherboard?. But on the otherside i hear a very annoying buzz out of the PSU it self. Its not loud but for a HTPC is pretty annoying. Does anybody else have this problem? Or cant you hear it over the loud PSU Fan? ;-)

11 - Posted by Kurtis on October 26, 2005 - 12:36 pm

This from Antec:

"We have received some complaints about Overture II not being quiet. Upon investigation these usually turn out to be related to the tachometer (fan speed connector) issue the Tech Lounge is asking about. Disconnecting the tachometer reduces the power supply fan speed to its normal range and quiets the case, and yes, our Customer Support people know to tell people about this simple fix. This issue is not a problem for cases manufactured after June 2005."

You apparently received one which was manufactured after June '05. You're sure the buzz is not the sound of the fan? Try unplugging the 3-pin connector trailing from the PSU and see if the noise persists and let me know what the outcome is.

You don't need that 3-pin connection plugged in, all it does is let you monitor the RPM of the PSU's fan with your BIOS or software.

12 - Posted by Kurtis on November 11, 2005 - 1:33 am

This articles has been updated with new information about the replacement power supply sent by Antec to replace the faulty unit that shipped with the original review sample which caused excessive noise.

13 - Posted by pgotera on November 28, 2005 - 4:13 pm

I have the case Overture 2, and the fan of the power supply is noisy. I read the article, i send one message to Antec,explaining the problem. I am to the delay of the answer.

I have disconnected the cable of the fan of the motherboard but it has increased the temperature. I have had to return to connect the fan to motherboard.

14 - Posted by Kurtis on November 28, 2005 - 5:24 pm

It increase the temperature because it is no longer spinning at full speed - you can't have both low temperatures and silence with air cooling, at least not in this specific situation. If you unplug the cable, as long as the fan is still spinning, the temperatures won't be a problem.

15 - Posted by pgotera on November 29, 2005 - 12:43 am

The problem is that the fan no spin, when disconnecting the cable. All the night been has disconnected, and the temperature has raised the 60 centigrados degrees.:-(
I am scared to fuse the power supply.

16 - Posted by Kurtis on November 29, 2005 - 1:37 pm

the fan shouldn't completely stop spinning - did you actually look to verify that it stopped spinning, or are you assuming it stopped because you can't hear it?

if it actually STOPPED spinning, you need to get in touch with antec to get a replacement PSU.

17 - Posted by Dyrewolph on November 30, 2005 - 3:08 am

which cable are you unplugging?

18 - Posted by Jimbo on December 31, 2005 - 7:31 am

Searching for help on noisy Overture II.
Had already exchanged PSU, similar packaging and PSU confusion (Overture I), to the review.
Just emailed Antec Techsupport for advice, found this review, will try the solution.
Thanks for the help

Add Comment

To add a comment without being a member, you may omit the password field, but you must enter your name (or nickname) along with your comment. * Denotes required fields.